Schlöder EMC Test Equipment

Schlöder develops and manufactures EMC Test & Measurement systems and EMC Components.



30 years of experience in EMC Test & Measurement systems and EMC Components

About Schlöder

Schlöder has over 30 years experience in developing EMC test equipment. Their range includes EFT / burst generators for tests according to the standard IEC / EN 61000-4-4 and ESD simulators. As an official UK distributor for Schlöder, MCS Test has the knowledge and experience to advise you on the full range of their test & measurement solutions.

Schlöder Products


EMC Generators

A generator is a machine that converts one form of energy into another, especially mechanical energy into electrical energy, as a dynamo, or electrical energy into sound, as an acoustic generator.

View products in EMC Generators

Immunity Test Systems

The purpose of RF immunity testing is to subject a product to a controlled RF stress that represents the likely level of stress that it might encountered in its operating environment, over a frequency range which is mostly dictated by practical aspects and experience of real-world problems.

View products in Immunity Test Systems

Voltage Interruption Simulators

Electrostatic discharge and conducted noise are well-known to cause malfunctions of electronics equipments. In the meantime, instant interruption and fluctuation of the power supply voltages can be also the causes.

View products in Voltage Interruption Simulators

Ferrite Clamps / Absorbing Clamps

An absorbing clamp, also know as a ferrite clamp, or ferrite choke, is a device used to reduce the amount of RF (radio frequency) noise, or interference, in a wire that conducts electricity. absorbing clamps are typically used to improve the performance of sound systems, including microphones.

View products in Ferrite Clamps / Absorbing Clamps


Coupling / Decoupling Networks are used to inject common mode disturbances to Equipment under Test (EuT). Further the CDNs provide sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal.

View products in CDNs

ESD Simulators

An ESD simulator, also known as an ESD gun, is a handheld unit used to test the immunity of devices to electrostatic discharge (ESD). These simulators are used in special electromagnetic compatibility (EMC) laboratories. ESD pulses are fast, high-voltage pulses created when two objects with different electrical charges come into close proximity or contact.

View products in ESD Simulators

Current Probes

A test probe is a physical device used to connect electronic test equipment to a device under test (DUT). Test probes range from very simple, robust devices to complex probes that are sophisticated, expensive, and fragile.

View products in Current Probes

IEC / EN 61000-4-2

IEC 61000-4-2 is the International Electrotechnical Commission's immunity standard on Electrostatic Discharge (ESD). The publication is one of the basic EMC standards of the IEC 61000–4 series. The European equivalent of the standard is called EN 61000-4-2. The current version of the IEC standard is the second edition dated 2008-12-09. The basic standards (61000-4) are usually called by product or family specific standards, which use the these basic standards as a common reference.

View products in IEC / EN 61000-4-2

IEC / EN 61000-4-4

IEC 61000-4-4 is the International Electrotechnical Commission's immunity standard based on electrical fast transient (EFT) / burst transients. This publication is part of the greater IEC 61000 group of standards which is covered under IEC TR 61000-4-1:2016. The current third version of this standard (2012) replaces the second version (2004). The goal of this standard is to establish a common and reproducible reference for evaluating the immunity of electrical and electronic equipment when subjected to electrical fast transient/bursts on supply, signal, control and earth ports.

View products in IEC / EN 61000-4-4

IEC 61000-4-6 Conducted Immunity

The IEC 61000-4-6 standard defines test procedures for the conducted immunity testing of electrical and electronic equipment to electromagnetic disturbances coming from intended RF transmitters in the 9 kHz to 80 MHz frequency range.

View products in IEC 61000-4-6 Conducted Immunity

Finance Your Schlöder Test Equipment

Renting your Schlöder equipment from MCS enables you to obtain the equipment you need now, without needing to rely on capital budget, compromise on quality, or spread the acquisition of multiple items over a number of years. We have a number of flexible finance packages available:


Rent to Buy

  • Spread payments up to five years
  • treat payments as operating expenses
  • rental payments count towards purchase

Flexible Finance

    • 0% finance options available
    • Terms between 1-24 months available
    • Available on all equipment

Operating Lease

    • Low rate for committed term
    • Low payments each month
    • Available on all equipment

Related Schlöder News

25 year old SESD 200 successfully calibrated

25 year old SESD 200 successfully calibrated

At the beginning of calendar year 2020, an old model of the "SESD 200" series successfully passed Schlöder's factory calibration in accordance with the IEC 61000-4-2 standard.

Find out more about 25 year old SESD 200 successfully calibrated
The New All-In-One Test Generator from Schloder

The New All-In-One Test Generator from Schloder

One of the very few combined IEC 61000-4-6 test systems that include the RF signal generator, a RF-power amplifier, a 3-channel RF voltmeter and a directional coupler for a very reasonable price.

Find out more about The New All-In-One Test Generator from Schloder
What is EMC?

What is EMC?

EMC - or Electromagnetic Compatibility to give it its full title - is the ability of an electronic device to work as intended within its environment.

Find out more about What is EMC?

Sign up for the MCS Newsletter

You will receive all the latest test & measurement news and rental offers.