Top Ten Requested Oscilloscopes This Year

How to Choose the Best Oscilloscope?

Published: 11th June 2021

An oscilloscope, formerly known as an oscillograph, is a benchtop instrument that graphically displays electrical signals and shows how those signals change over time. They are used by engineers to troubleshoot circuits and check signal quality. Most engineers use a digital oscilloscope, which is what we’re going to focus on here. Digital oscilloscopes acquire and store waveforms, which show a signal’s voltage, frequency, the portion of the signal that is noise, whether the signal is distorted, the timing between signals and more.

But when it comes to choosing the best oscilloscope, how do you know which oscilloscope is right for your application? There are 10 primary factors to consider when you buy an oscilloscope. For a quick overview of the top factors, watch the short video below. Otherwise, keep reading for the full details on how to choose an oscilloscope for your application.

Oscilloscope bandwidth

System bandwidth determines an oscilloscope’s ability to measure a signal. Specifically it determines the maximum frequency that the instrument can accurately measure. Bandwidth is also a key determining factor in price.

Determine what you need – use the ‘five times rule’

For example, a 100 MHz oscilloscope is usually guaranteed to have less than 30% attenuation at 100 MHz. To ensure better than 2% amplitude accuracy, inputs should be lower than 20 MHz. For digital signals, measuring rise and fall time is key. Bandwidth, along with sample rate, determines the smallest rise-time that an oscilloscope can measure.

The probe and oscilloscope form a measurement system that has an overall bandwidth. Using a low-bandwidth probe will lower the overall bandwidth, so be sure to use probes that are matched to the scope.

Oscilloscope rise time

Rise time describes the useful frequency range of an oscilloscope, and this is a critical measurement in the digital world. Rise time is often considered when measuring digital signals like pulses and steps.

Determine what you need – use the ‘five times rule’

In order to accurately capture the details of rapid transitions, an oscilloscope must have sufficient rise time. Fast rise time is also needed for accurate time measurements. To calculate the oscilloscope rise time required for your signal type, use this equation:

For instance, a 4-ns rise time needs a scope with faster than 800 ps rise time. Note: As with bandwidth, achieving this rule of thumb may not always be possible. Many logic families have faster rise times (edge speeds) than their clock rates suggest. A processor with a 20 MHz clock may well have signals with rise times similar to those of an 800 MHz processor. Rise times are critical for studying square waves and pulses.

Oscilloscope sample rate

The sample rate of an oscilloscope is similar to the frame rate of a movie camera. It determines how much waveform detail the scope can capture.

Determine what you need – use the ‘five times rule’

Sample rate (samples per second, S/s) is how often an oscilloscope samples the signal. Again, we recommend a ‘five times rule’. Use a sample rate of at least 5x your circuit’s highest frequency component.

Oscilloscopes come with a wide variety of sample rates, from 1 to 200 GS/s, to meet the needs of your application.

The faster you sample, the less information you’ll lose and the better the scope will represent the signal under test. However, fast sampling will also fill up your memory quickly, which limits the time you can capture.

Channel density of an oscilloscope

Digital oscilloscopes sample analog channels to store and display them. In general, the more channels the better, although adding channels adds to the price.

Determine what you need

Your application will determine whether you need to choose an oscilloscope with two, four, six, or even eight analog channels. Two channels let you compare a component’s input to its output, for example. Four analog channels let you compare more signals and provides more flexibility to combine channels mathematically (multiplying to get power, or subtracting for differential signals, for example). Oscilloscopes with six or eight channels allows for multiple bus analysis while simultaneously viewing voltage or current type signals in a power related environment.

A Mixed Signal Oscilloscope adds digital timing channels, which indicate high or low states and can be displayed together as a bus waveform. Whatever you choose, all channels should have good range, linearity, gain accuracy, flatness, and resistance to static discharge.

Some instruments share the sampling system between channels to save money. But beware: the number of channels you turn on can reduce the sample rate.

Consider compatible oscilloscope probes

Good measurements begin at the probe tip. The scope and probe work together as a system, so be sure to consider probes when selecting an oscilloscope.

When taking measurements, probes actually become a part of the circuit, introducing resistive, capacitive, and inductive loading that alters the measurement. To minimize the effect, it’s best to use probes that are designed for use with your scope.

Select passive probes that have sufficient bandwidth. The probe’s bandwidth should match that of the oscilloscope.

A broad range of compatible probes will allow you to use your scope in more applications.

Check to see what’s available for the scope before you buy.

Use the right probe for the job

Passive probes: Probes with 10X attenuation present a controlled impedance and capacitance to your circuit, and are suitable for most ground-referenced measurements. They are included with most oscilloscopes – you’ll need one for each input channel.

High-voltage differential probes:
Differential probes allow a ground-referenced oscilloscope to take safe, accurate floating and differential measurements. Every lab should have at least one.

Logic probes:
Logic probes deliver digital signals to the front end of a Mixed Signal Oscilloscope. They include “flying leads” with accessories designed to connect to small test points on a circuit board.

Current Probes:
Adding a current probe enables the scope to measure current, of course, but it also enables it to calculate and display instantaneous power.

Triggering capabilities of an oscilloscope

All oscilloscopes provide edge triggering, and most offer pulse width triggering. To acquire anomalies and make best use of the scope’s record length, look for a scope that offers advanced triggering on more challenging signals.

Determine what you need

The wider the range of trigger options available the more versatile the scope (and the faster you get to the root cause of a problem):

  • Digital/pulse triggers: pulse width, runt pulse, rise/fall time, setup-and-hold
  • Logic triggering
  • Serial data triggers: embedded system designs use both serial (I2C, SPI,CAN/ LIN…) and parallel buses.
  • Video triggering

Oscilloscope record Length

Record length is the number of points in a complete waveform record. A scope can store only a limited number of samples so, in general, the greater the record length, the better.

Determine what you need

Time captured = record length/sample rate. So, with a record length of 1 Mpoints and a sample rate of 250 MS/sec, the oscilloscope will capture 4 ms. Today’s scopes allow you to select the record length to optimize the level of detail needed for your application.

A good basic scope for example will store over 2,000 points, which is more than enough for a stable sine-wave signal (needing perhaps 500 points), whilst more advanced high-end scopes would have up to 1Gpoints, which is essential for working with high-speed serial data type applications.

Oscilloscope waveform capture rate

Waveform capture rate, expressed as waveforms per second (wfms/s), refers to how quickly an oscilloscope acquires waveforms. The waveform capture rates of oscilloscopes vary greatly, so it’s important to find the right one for your application.

Determine what you need

Oscilloscopes with high waveform capture rates provide significantly more visual insight into signal behavior, and dramatically increase the probability that the oscilloscope will quickly capture transient anomalies such as jitter, runt pulses, glitches and transition errors.

Digital storage oscilloscopes (DSO) employ a serial processing architecture to capture from 10 to 5,000 wfms/s. Some DSOs provide a special mode that bursts multiple captures into long memory, temporarily delivering higher waveform capture rates followed by long processing dead times that reduce the probability of capturing rare, intermittent events.

Most digital phosphor oscilloscopes (DPO) employ a parallel processing architecture to deliver vastly greater waveform capture rates. Some DPOs can acquire millions of waveforms in just seconds, significantly increasing the probability of capturing intermittent and elusive events and allowing you to see the problems in your signal more quickly.

Oscilloscope expandability

As your needs change, you want an oscilloscope that can accommodate your needs with application modules and software updates.

Determine what you need

If you want to expand the capabilities of your oscilloscope over time, make sure your instrument has everything you need. For instance, some oscilloscopes allow you to:

  • Add memory to channels to analyze longer record lengths
  • Add application-specific measurement capabilities
  • Complement the power of the oscilloscope with a full range of probes and modules
  • Work with popular third-party analysis and productivity
  • Windows-compatible software
  • Add accessories, such as battery packs and rack mounts

Connectivity of an oscilloscope

After you’ve analyzed your oscilloscope measurements, you’ll need to document and share your findings. The connectivity of an oscilloscope delivers advanced analysis capabilities and simplifies the documentation and sharing of results.

Determine what you need

Depending on the oscilloscope, you may have access to standard interfaces (GPIB, RS-232, USB, and Ethernet), network communication modules, or advanced features that allow you to:

  • Create, edit and share documents on the oscilloscope, all while working with the instrument in your particular environment
  • Access network printing and file sharing resources
  • Access the Windows® desktop
  • Run third-party analysis and documentation software
  • Link to networks
  • Access the Internet
  • Send and receive e-mail

MCS Test are the approved UK partner for Tektronix
Content Source: How to choose the best oscilloscope | Tektronix


Tektronix MDO32 100 MHz - 1 GHz Mixed Domain Oscilloscope

Frequency Range: 100 MHz - 1 GHz
2 Analog Channels, 16 Digital (OPT)

With the largest display in class, improved low-level signal measurement accuracy and industry-leading probe performance, the MDO32 sets a new standard for bench oscilloscopes. Whether you’re testing your baseband design for IoT or just for simple EMI sniffing, the MDO32 has a unique true hardware spectrum analyzer built right in with superior RF test performance and guaranteed RF specifications.

Find out more about Tektronix MDO32 100 MHz - 1 GHz Mixed Domain Oscilloscope

Tektronix MDO34 100 MHz - 1 GHz Mixed Domain Oscilloscope

Frequency Range: 100 MHz - 1 GHz
4 Analog Channels, 16 Digital Channels (OPT)

With the largest display in class, improved low-level signal measurement accuracy and industry-leading probe performance, the MDO34 sets a new standard for bench oscilloscopes. Whether you’re testing your baseband design for IoT or just for simple EMI sniffing, the MDO34 has a unique true hardware spectrum analyzer built right in with superior RF test performance and guaranteed RF specifications.

Find out more about Tektronix MDO34 100 MHz - 1 GHz Mixed Domain Oscilloscope

Tektronix TBS1052C 50 MHz Digital Storage Oscilloscope

Frequency Range: 50 MHz
Analog Channels: 2

The TBS1052C Digital Storage Oscilloscope offers affordable performance in a compact design.

Find out more about Tektronix TBS1052C 50 MHz Digital Storage Oscilloscope

Tektronix MSO5204B 2 GHz Mixed Signal Oscilloscope

Please note, the supply of MSO/DPO5000B Series Oscilloscopes is limited. New 5 Series MSO oscilloscopes are the recommended replacements for the MSO/DPO5000B Series.
Learn about the new 5 Series MSO Oscilloscopes.

The MSO5204B Oscilloscope is designed for engineers debugging and verifying complex systems.

Find out more about Tektronix MSO5204B 2 GHz Mixed Signal Oscilloscope

You Might also like

MSO24 Auto

Bringing Portability and Power to the Automotive Industry with the 2 Series MSO

The modern automotive industry moves quickly, and automotive engineers and technicians need the right tools at their fingertips to identify issues quickly and easily. There are many diagnostic tools that analyze the performance of different vehicle systems on any given day, but these instruments almost always include an oscilloscope, which displays different voltages and helps automotive technicians troubleshoot various electrical components under the hood.

Read more
MS068 B Embedded

Advanced Oscilloscope Analysis – 4 Unique Capabilities with the 6 Series B MSO

With the lowest input noise and up to 10 GHz analog bandwidth, the 6 Series B MSO provides the best signal fidelity for analysing and debugging today's embedded systems with GHz clock and bus speeds.

Read more
Abstract Power Analysers

Forming the Best Solution for Battery Formation and Aging

Current markets are leading to high demand for battery cells. One way for manufacturers to increase throughput is to reduce the time spent making each battery. The formation and aging stage is the most time consuming part of the cell manufacturing process. Ensuring that the right equipment is used for the job can help with some of the challenges facing formation and aging.

Read more

Sign up for the MCS Newsletter

You will receive all the latest test & measurement news and rental offers.