How to Create Handover Testing and Manipulate Fading Simulation Tests

How to Create Handover Testing and Manipulate Fading Simulation Tests

Published: 2nd March 2020

Digital attenuators are a critical part of mobile network test platforms where flexibility in controlling signal strength is vital. Multipath fading is a commonly occurring problem with obstacles, such as mountains or buildings, absorbing and reflecting signals. Programmable attenuators’flexible features can be used in fading simulation applications where multipath scenarios can occur. For example, in handover testing, radar processing, digital radio communications, and GPS receivers. In these cases, the fading simulator and customized test system with multipath switching is the key to optimizing mobile network performance.

Handover: Handover in Theory

A handover, or handoff, occurs when an outgoing cellular call is transferred from one cell to the an adjacent cell as the cellphone is moving through the network coverage area. Cells are physical areas that have cellular coverage. Handover is used with cellular networks, such as LTE or wifi networks. Some cellular services, including Google’s Project Fi, can even enable handovers between WiFi and LTE with intelligent handover techniques.

Cellular networks must rely on multiple frequency channels as any signals sent out by a base station can be attenuated by obstacles in the environment. Soft handovers were developed for the goal of a seamless call transition in cases where calls become unreliable due to fading. This is where a connection to the current cell is only broken after a steady connection to the target cell is established known as ‘make-before-break’. Hard handover occurs when the mobile connection from the source is broken and the connection to the target is made afterwards also known as a ‘break-before-make’. Hard handovers allow for a more efficient use of channels as only one channel is necessary to enable a hard handover, which simplifies the design of the mobile phone as it also does not necessitate the need for parallel processing of several channels. While soft handovers can require more channels and a mobile phone that can receive two or more channels in parallel, the chances of a signal in all the channels being interrupted is much lower, in other words, dropped calls are highly unlikely in soft handover networks.

Handover can occur between “sectors” of the same site, known as intra system handover. Sectors are different areas of coverage from the same base station, and multiple ‘sectors’ can occupy one ‘cell’. Inter system handover can often occur with a fast moving target, where the target connection is established from one cell to a completely different cell or base station. More recently, cellular technological advances have enabled vertical handover, such that a mobile phone connects between cellular networks and wireless LAN (WLAN) for greater accessibility. While cellular networks can offer lower data rates over large areas, WLAN technologies can potentially compensate for this as it offers higher data rates over smaller areas.

Handover Applied

Firstly, network engineers generate a ‘neighbor list’ of potential target cells for handover from selected source cells. Then, as a call is ongoing, the source channel’s signal transmission strength is monitored to assess when a handover request by the mobile phone of base station is necessary. In this complex process, the base stations in the ‘neighbor list’ and the mobile phone are connected and monitoring each other for the best target cell to connect to. vx-blog-handover-examples-p1.jpg9 Various types of handovers that can occur for better user connection and overall accessibility.

Network engineers have enabled several monitoring methods to ensurehandover takes place seamlessly. The parameters that are tracked are dependent on the types of network modes that the mobile phone receiver and base station antenna is communicating with—some of these modes include GSM, UMTS, LTE, and CDMA. Ultimately, the received signal level and received signal quality is tracked in the network measurement reports (NMR). Although, this is more complex with vertical handover where metrics should include user preference, network conditions, application types, cost, etc. In GSM networks, the Rxlevel indicates the power level of the received signal and is measured in decibels (dBm) and RxQual is an integer value representing the quality of voice at the receiver. The integer value of RxQual corresponds to the number of bit errors in a number of bursts. For UMTS, the received signal code power (RSCP) is another measurement of received signal power over a communication channel, and is measured in dBm. The Ec/Io is the ratio of the received energy per chip and the interference level measured in dB. In LTE handover measurements, the reference signal received power (RSRP) is used to estimate path loss, while reference signal received quality (RSRQ) indicates the quality of the received reference signal. In essence, RSRQ is a ratio between RSRP and the reference signal strength indicator (RSSI).

You Might also like

Vx update tb handover test 2021 2

Tech Brief Provides Insight on Creating Wireless Handover Tests and Fading Simulations with Low-cost Programmable Devices

Handover testing is a crucial stage in the development and deployment of wireless systems in which the cellular devices are in motion. A handover is most simply envisioned as a person driving down an interstate highway while on a cellular call and the call being long enough in duration to necessitate that it is handed over to the next cell tower in proximity to the car as the call begins to fade away from its originating tower.

Read more
Polygon lines and dots connection

How to set up radar testing with FMCW and chirp capability using low-cost programmable RF signal generators

FMCW and chirp (pulsed linear frequency modulated) radar are some of the most common radars used globally. These types of radar are designed for electronic warfare (EW) and defense, as well as a variety of commercial aerospace applications. In the case of defense, FMCW and chirp signals are commonly used in terrain-following radar for under-the-radar flying, surveillance, and for targeting systems.

Read more
Wireless Network Above Europe

Putting the Less in Wireless Testing

“Wireless testing” is defined as the actions necessary to assess a device's capability to first, properly and securely connect with other devices and networks, and second, complete the desired operational tasks expected of the connected device successfully.

Read more

Sign up for the MCS Newsletter

You will receive all the latest test & measurement news and rental offers.